Sympodium DT770®Interactive Pen DisplayInstallationGuide
4 OverviewRoom Control Interface ButtonYou can open room control interface menus using the button in the top-left of the DT770 (room control system no
Overview 5• the Status indicator is illuminated and green when the DT770 is communicating with SMART Board software correctly For information on the P
6 Overview
Installing the DT770 7Installing the DT770This chapter tells you how to:• determine the best location for the DT770 (this page)• remove the connection
8 Installing the DT770Removing the Connection Panel’s Protective CoverWhen you initially receive your DT770, the connection panel is inaccessible beca
Installing the DT770 92. Connect the supplied VGA (RGB) video cable to the Analog RGB IN port on the DT770.3. Connect the other end of the video cable
10 Installing the DT7703. Place the pen in the recess below the interactive screen so that it’s available for use. The recess holds the pen magnetical
Installing the DT770 11Mounting the DT770 on a Mono StandIf you want to mount the DT770 at an angle of 30 or 45 degrees, you can install the DT770 on
12 Installing the DT770Securing the DT770You can secure the DT770 by attaching a cable (not supplied) between an immovable object and the Kensington®
Installing the DT770 13NOTE: If SMART Board software doesn’t recognize the DT770, activate the port manually using an attached keyboard or mouse. For
FCC WarningTrademark NoticeCopyright NoticeThis equipment has been tested and found to comply with the limits for a Class A digital device, pursuant t
14 Installing the DT770Orienting the ScreenTo ensure that the pointer appears directly beneath your finger or the tethered pen when you touch the DT77
Using the DT770 15Using the DT770The Sympodium DT770 interactive pen display is as easy to use as a pen on paper. By touching your finger or the tethe
16 Using the DT770When you’re not using the tethered pen, place it in the recess on the front of the DT770, where it’s held in place magnetically. NOT
Using the DT770 17Press the Pointer button and then press your finger or the tip of the tethered pen on the interactive screen to activate an object.
18 Using the DT770To save your note as part of the file in an Aware application, save the file as you normally would. In some Windows applications, su
Using the DT770 19• Floating Tools: a virtual palette of toolsNOTE: For more information on using or customizing the Screen Capture tools, the SMART K
20 Using the DT770Using the Room Control Interface ButtonYou can press the Room Control Interface button to open room control interface menus (room co
Using the DT770 213. Press the large Pen Tray button on the left side of the dialog.4. To change the function of the Keyboard function button or the R
22 Using the DT7701. Press the SMART Board icon in the system tray (Windows operating systems) or in the Dock (Mac computers), and press Control Panel
Cleaning the DT770 23Cleaning the DT770This chapter offers you advice on cleaning the DT770. Cleaning the Interactive Pen DisplayTurn off the DT770 be
Important Information iImportant InformationWARNINGIf the screen is damaged, don’t touch any liquid that leaks from it. This liquid is an irritant. If
24 Cleaning the DT770Cleaning the Tethered PenTo clean the tethered pen, gently wipe the pen with a damp cloth. CAUTIONThe tethered pen is a sealed u
Troubleshooting 25TroubleshootingThis chapter offers suggestions for troubleshooting your DT770.Checking the Power of the Interactive Pen DisplayThe P
26 TroubleshootingChecking the Status of the Interactive Pen DisplayThe Status indicator shows whether the interactive pen display is communicating wi
Troubleshooting 27Control and Writing ProblemsIf the pointer doesn’t accurately follow the movement of the tethered pen or your finger, orient the DT7
28 TroubleshootingCalibrating the CamerasDigital cameras in the corners of the interactive screen are calibrated to recognize the position of your fin
Appendix A: Adjusting the Screen Settings 29Appendix A: Adjusting the Screen SettingsYou can fine-tune the screen settings by using the DT770’s Displa
30 Appendix A: Adjusting the Screen Settings3. Press the Menu button.NOTE: The new settings are saved when you press the Menu button.4. Repeat step 3
Waste Electrical and Electronic Equipment (WEEE) Regulations 31Waste Electrical and Electronic Equipment (WEEE) RegulationsWaste Electrical and Electr
32 Waste Electrical and Electronic Equipment (WEEE) Regulations
Customer Support 33Customer SupportTrainingDo you need training on your SMART product? Visit http://smarttech.com/trainingcenter for free training mat
ii Important InformationOther Precautions For proper installation, read this guide carefully and observe the following precautions. • Don’t place shar
34 Customer SupportGeneral InquiriesMain Switchboard: 1.888.42.SMART (toll-free in Canada/U.S.) or +1.403.245.0333 (all other countries)Fax: +1.403.2
Index 35IndexAAdjusting Screen Display Settings 29CCalibrating the Cameras 28Cleaning the DT770 23Connecting the DT770 8Connecting the Tethered Pen 9C
36 IndexTTethered PenClicking 16Connecting 9Introduction 2Using 15Writing 17Tilt Stand 11TroubleshootingControl and Writing 27Image 26Power 25Status 2
99-00580-01 REV A0SMART Technologies Inc.1207 – 11 Avenue SW, Suite 300Calgary, AB T3C 0M5CANADASupport +1.403.228.5940 or Toll Free 1.866.518.6791 (C
Table of Contents iiiTable of ContentsImportant Information...
iv Table of ContentsTroubleshooting...
Overview 1Overview The Sympodium® DT770 interactive pen display works with your computer and SMART Board™ software to create an interactive presentati
2 Overview• a USB 2.0 high speed hub to which you can connect a USB memory storage deviceThis guide describes how to install and use the DT770 with yo
Overview 3NOTE: For the DT770 to interpret the location of the tethered pen, the connected computer must be running SMART Board tools. You’ll know tha
Comments to this Manuals